Dwyer Instruments

Dwyer pitot tubes, series 160 are constructed from corrosion resistant stainless steel for a lifetime of service. No correction factors or calibration required. Various standard sizes are available for use in small and large ducts.

Serves as pressure source to calibrate gages and transmitters or to set pressure switches. Use with manometer or other pressure standard. Generate pressures from a fraction of an inch w.c. to 72 psig (5 bar). Includes barbed fitting, tee connector and three 36? lengths of vinyl tubing.

The Dwyer Magnehelic can be mounted in different ways. By default, the instrument is equipped with all the accessories needed to mount the Magnehelic into a round hole in a panel. In addition, there are various accessories for mounting on a round tube, in a (system) wall, or with various brackets in a wall cabinet.

The Dwyer CDT series CO2 transmitters are equipped with an NDIR (infrared) sensor. The transmitters are available in a wall-mounted version and in a version for duct mounting. Optionally, the transmitters are also available with a temperature output and SPST relay contact. Unique for this CO2 measurement is that it can also be used for rooms that are used 24 hours a day. Other sensors use the p...

The Dwyer PMT2 series is a particle transmitter designed for broken bag detection (fiter leak detection). The special electrostatic induction technology detects particles that flow past the sensor and converts this into a 4 to 20 mA signal based on the concentration of these particles. The PMT2 offers 6 sensitivity ranges that allow the user to choose the range that best fits the application. T...

De TE-A serie bestaat uit middelende temperatuursensoren voor grote kanalen en luchtbehandelingskasten. De buigbare aluminium sensoren zijn verkrijgbaar in lengtes van 150, 300 en 600 mm. Deze capillairen bestaan uit vier temperatuursensoren die intern worden gemiddeld. De CC1-montagebeugels zijn beschikbaar om de capillair op de wand van de buis of luchtbehandelingsunit te monteren zonder de s...

De TE-OND serie bestaat uit passieve temperatuursensoren voor het meten van temperaturen buiten. De temperatuursensoren zijn geschikt om buiten te monteren, maar niet in direct zonlicht. Voor montage in direct zonlicht raden we een uitvoering met weerhut aan. De TE-OND serie is verkijgbaar met PT100, PT1000, 3 kOhm, 10 kOhm en 20 kOhm uitgangen.

De TE-RND serie bestaat uit passieve temperatuursensoren voor buiten. De weerhut maakt de TE-RND serie ook geschikt voor plaasing in direct zonlicht. De TE-RND serie is verkijgbaar met PT100, PT1000, 3 kOhm, 10 kOhm en 20 kOhm uitgangen.

De O-4 serie bestaat uit passieve temperatuursensoren voor het meten van temperaturen in de buitenlucht. De O-4 serie is verkijgbaar met PT100, PT1000, 3 kOhm, 10 kOhm en 20 kOhm uitgangen.

Rugged and reliable the Series L4 Flotect Level switch operates automatically to indicate tank level. Perfect for starting or stopping pumps, opening or closing valves, or actuate level alarm signals. Horizontal installation or optional top mount vertical installation. ATEX version available.

Model L8 Flotect Liquid Level Switch features a leak proof body and float constructed from tough, durable polyphenylene sulfide which has excellent chemical resistance. This compact and reliable control is designed to handle temperatures up to (100°C and pressures to 10 bar.

The MBLT miniature submersible level transmitter is only 0.63˝ in diameter making it ideal for level monitoring in well and borehole applications with 4 to 20 mA or 0 to 5 V output. Designed for years of trouble free service, the MBLT has a welded 316 SS body and 316 SS nose cap. Body top is also 316 SS and tapered to prevent damage or snares when pulling the unit out of the installation. Featu...

The Dwyer SAH Smart Air Hood is a revolution in the field of balometers. The patented design ensures minimal resistance and the balometer is pre-calibrated for each type of grid. This makes the SAH the most reliable balometer on the market. The hood can easily be clamped between the floor and the ceiling with the included telescopic rod. The readout device communicates wirelessly with the hood...

De BTT-O serie bestaat uit temperatuurtransmitters voor buitenlucht. De temperatuurtransmitters kunnen worden uitgevoerd met een 0-10V of 4-20mA uitgang. De spatwaterdichte behuizing kan buiten worden toegepast. Voor plaatsing in direct zonlicht adviseren we een versie met weerhut.

De TE-WSS temperatuursensoren zijn vervaardigd uit RVS en kunnen vlak in een wand gemonteerd worden. Het robuuste RVS ontwerp maakt de TE-WSS serie geschikt voor industriële ruimtes, cleanrooms, maar ook in bijvoorbeeld klaslokalen. De TE-WSS serie is er in verschillende uitvoeringen, zoals; PT100, PT1000 en verschillende NTC varianten.

Model 485B is a compact, hand-held instrument for measuring percentage of relative humidiy and temperature in °C or °F and also calculates dew point and wet bulb temperature. It will store up to 99 readings, ideal for technicians meeding to take multiple readings for later analyses.

Series 477 handheld digital manometers are packed with features you need to make pressure measurement and recording faster, easier and more accurate than ever. You can instantly select from up to nine of the most widely used pressure units. A non-volatile memory function enables storage of up to 40 readings. Other main features are: display HOLD, audible alarm, visual alarm, backlight with au...

Series 490A Digital Manometers are versatile, hand-held, battery operated manometers available in several basic ranges for positive or positive differential pressure measurement and can tolerate most liquid media compatible with 316LSS. A memory function allows storage of up to 40 readings.

The Dwyer TE-D series consists of highly priced temperature sensors for installation in air ducts. There are several outputs that allow the sensor to be read on any type of Building automation system.

The Dwyer TE-E series consists of very competitively priced temperature sensors for mounting in walls on the wall. There are several outputs for each type of BMS possible

The BTT series temperature transmitters are ideal for measuring temperature in air ducts. Sensor lengths of up to 450 mm insertion are possible for duct mounting sensors. The plastic terminal box with fastening tabs makes the installation easier.

The Dwyer BTT-E series is a simple space temperature transmitter for wall mounting. For the analogue output, you can choose between 4-20 mA and 0-10 V, so that the transmitters can be connected to any BMS.

The Dwyer BTT-R series is a temperature transmitter for outdoor mounting with radiation shield. The weather shelter ensures that the temperature measurement is not affected by direct sunlight. The BTT-R temperature transmitter has an analogue output for coupling to each building management system.

These inexpensive manometers measure positive, negative and differential pressures. Dwyer Flex-Tube U-Tube Manometers combine the inherent accuracy of the simple "U" Tube with the durability of tough, long-lasting plastic construction. Series 1221 Manometer, the simplest, lowest cost basic U-gage. Series 1222 Manometer, alll the features of the 1221 plus magnetic clips. Series 1223 Manometer, t...

The most popular differential pressure switch combines advanced design and precision construction to make these switches able to perform many of the tasks of larger, costlier units. Designed for air conditioning service, they also serve many fluidics, refrigeration, oven and dryer applications. For air and non combustible compatible gases, Series 1910 switches have set points from 18 to 400 Pa...

Model 1950 explosion proof pressure pressure switch combines the best features of the popular1900 series with an integral explosion-proof and weatherproof housing, making it an exceptional value for either application. It is CE, UL and CSA listed, FM approved for use in Class I, Div 1, Groups C and D, Class II Groups E, F, and G and Class III hazardous atmospheres (NEMA 7 & 9), Raintight NEMA 3...

The Model 1950G Explosion-Proof Switch combines the best features of the popular Dwyer® Series 1950 Pressure Switch with the benefit of natural gas compatibility. Units are rain-tight for outdoor installations, And are ATEX approved CE ATEX II 2G Exd IIB+H2 T6. Adjustment to the set point of the switch can be made without disassembly of the housing.

Dwyer Magnehelic gage for high accuracy, guaranteed within 2% of full scale and for the wide choice of 81 models available to suit your needs precisely. Using Dwyer's simple, frictionless Magnehelic gage movement, it quickly indicates low air or noncorrosive gas pressures, either positive, negative (vacuum) or differential. The design resists shock, vibration and over-pressures. No manometer fl...

The Minihelic is a small differential pressure manometer, suitable for many of the same applications as the Magnehelic gage where the greater accuracy, sensitivity, and higher and lower differential pressure ranges of the Magnehelic gage are not required. It can safely operate at total pressures up to 200 kPa. With the housing molded from mineral and glass filled nylon and the lens molded from...

The series 3000MR Photohelic switch/gages combine the functions of a precise, highly repeatable differential pressure switch with a large easy-to-read analog pressure gage employing the durable, time-proven Magnehelic gage design. The Photohelic has 2 switch functions. Switch setting is easy to adjust with large external knobs on the gage face. Gage reading is unaffected by switch operation — w...

The Capsuhelic gage is designed to give fast, accurate indication of differential pressures. The gage may be used as a readout device when measuring flowing fluids, pressure drop across filters, liquid levels in storage tanks and many other applications involving pressure, vacuum or differential pressure.

The Model AAFS air flow switch provides excellent sensitivity and reliability at a very reasonable price. Quality features include a rugged die cast body, stainless steel vane and SPDT snap switch. Unit is field adjustable from 400-1600 FPM. Mounting is fast and simple,with only two screws needed. Vane fits 6 inch or larger ducts.

The Series 605 Magnehelic Indicating Transmitter provides for both visual monitoring and electronic control of very low differential pressure. The Series 605 is ideal for control applications in building HVAC systems The easily read dial gage is complimented by the two-wire, 4-20 mA control signal utilizing the timeproven Dwyer® Magnehelic® gage mechanical design and Series 600 transmitter tech...

The Series 629C Differential Pressure Transmitter monitors differential pressure of air and compatible gases and liquids with 0.5% accuracy. The design employs dual pressure sensors converting pressure changes into a standard 4-20 mA output signal for two wire circuits. Small internal volume and minimum moving parts result in exceptional response and reliability.

The Series ADPS Adjustable Differential Pressure Switch is designed for pressure, vacuum, and differential pressures. The adjustment knob allows changes to the switching pressure to be made without a pressure gage. The ADPS is available with settings from 20 Pa up to 5000 Pa. The compact size, adjustment knob and low cost make the ADPS the perfect choice for HVAC applications.

The Dwyer series DM-2000 differential pressure transmitter senses the pressure of air and compatible gases and sends a standard 4-20 mA output signal. The DM-2000 housing is specifically designed to mount in the same diameter cutout as a standard Magnehelic gage. A wide range of models are available factory calibrated to specific ranges. Pressure connections are inherent to the glass filled pla...

The Series DPG has a high ±0.25% full scale accuracy. The 4 digit digital display will reduce the potential for errors in readings by eliminating parallax error commonly produced with analog gages. Series DPG is battery powered and has an auto-shut off to conserve battery life. Battery life, on average, will last 2000 hours. A 4 button key pad allows easy access to features without the need to...

The Series DPG-200 digital pressure gage has a precise ±0.25% full scale accuracy. The 4 digit digital display will reduce the potential for errors in readings by eliminating parallax error commonly produced with analog gages. The DPG-200 is packaged in a durable extruded aluminum case (IP66). The unit is powered by 12-24 VDC/VAC and contains two alarm set points along with a 4-20 mA process ou...

The series DPGA is the only economic digital pressure gage with selectable engineering units on the market. With its 1% accuracy and digital push-button zero, the DPGA is the perfect choice for digitally monitoring the pressures of air and compatible gases.

The Series DPGW is the only economic digital pressure gage for liquids with the ability to select engineering units on the market. With its 1% accuracy and digital push-button zero, the DPGW is the perfect choice for digitally monitoring the pressures of compatible liquids and gases. The 4 digit digital display will reduce the potential for errors in readings by eliminating parallax error commo...

Explosion-proof, heavy duty, industrial pressure switch which provides sensitivity to differential pressure as low as 25 mbar up to 14 bar with a max. static pressure of 100 bar. This unit has a standard aluminium pressure chamber but is also available in 316 stainless steel. Approvals : UL, CSA, CE and ATEX.

Dwyer Mark II series molded manometers are of the inclined and inclined-vertical types. The curved inclined-vertical tube of the Mark II manometers can be mounted on any vertical surface with the two mounting screws provided. Ranges available from 0-80 mmH2O and from -10 to + 700 Pa.

The MP Mini-Photohelic differential pressure switch/gage combines the time proven Minihelic II differential pressure gage with two SPDT switching setpoints. The Mini-Photohelic gage is designed to measure and control positive, negative, or differential pressures consisting of non-combustible and non-corrosive gases. Gage reading is independent of switch operation. This extremely compact switch...

The Series MS Magnesense Differential Pressure Transmitter is an extremely versatile transmitter for monitoring pressure and air velocity. This compact package is loaded with features such as: field selectable english or metric ranges, field upgradeable LCD display, adjustable dampening of output signal (with optional display) and ability to select a square root output for use with pitot tubes...

The Dwyer RHP-E series is a combined room temperature and humidity sensor for wall mounting. There can be chosen from different accuracies and a housing with or without display. There are several outputs that allow the sensor to be read on any type of GBS.

The Rate-Master® flowmeter line of direct reading precision flowmeters incorporates many unique user features at moderate cost. These low cost flowmeters are ideal for general use.

Dwyer SA 1100 is an extremely rugged pressure switch that assures excellent reliability. The pressure switch has a visual setpoint and an adjustable deadband, up to 5% of measuring range. Wetted parts are available in aluminium and stainless steel.